Operating Instructions
Thank you for purchasing this high-resolution multi-scan color monitor.
Please read this guide thoroughly before installation.
FCC RADIO FREQUENCY INTERFERENCE STATEMENT
WARNING: (FOR FCC CERTIFIED MODELS)
This monitor has been tested and found compliant with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide proper protection against harmful
interference to a residential installation. This monitor generates, uses,
and can radiate radio frequency energy. Harmful interference to radio
communication may result if it is not properly installed and used.
However, there is no guarantee that interference will not occur in a
particular installation. If this monitor does cause serious interference
to radio or television reception, resetting the monitor may resolve the
problem. Moreover, users are encouraged to correct interference by
doing one or more of the following:
l Reposition or relocate the receiving antenna.
l Move the monitor and the receiver further away from each other.
l Connect the monitor into an outlet on a circuit different from that
to which the receiver is connected.
l Consult your local dealer or a qualified technician.
FCC Warning:
To assure a continued FCC compliance, a user must use a grounded
power supply cord and the provided shielded video interface cable with
bonded ferrite cores. Also, any unauthorized changes or modifications to
this monitor will void the user’s authority to operate this device.
Note: If necessary, shielded interface cables and the A.C. power cord
must be used to meet the emission level limits.
EMI Certification
The Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulation. Cet appareil numerique de
class B respecte toutes les exigences du Reglement sur Ic materiel
brouilleur du Canada.
2
Safety Precautions
This monitor is manufactured and tested on the principle that the user’s
safety comes first. However, improper use or installation may not only
damage the monitor but endanger the user as well. As a safety
precaution, go over the following WARNINGS carefully before installation,
and keep this guide handy.
Warnings:
l
This monitor should be operated only at the correct power sources
indicated on the label at the rear end of the monitor. If you are unsure
of the power supply in your residence, consult your local dealer or
Electricity Supplier.
l
l
Do not try to repair the monitor yourself, as it contains no
user-serviceable parts. The monitor should only be repaired by a
qualified technician.
Do not remove the monitor cabinet. There are high-voltage parts
inside that may cause an electric shock even when the power cord
is disconnected.
l
l
l
Stop using the monitor if the cabinet is damaged. Have it checked by
a service technician.
Put your monitor only in a clean, dry environment. Unplug the monitor
immediately if it gets wet, and consult your service technician.
Always unplug the monitor before cleaning it. Clean the cabinet with
a clean, dry cloth. Apply non-ammonia-based cleaner onto the cloth,
not directly onto the glass screen.
l
Keep the monitor away from magnetic objects, motors, TV sets, and
transformers.
l
l
Do not place heavy objects on the cable or power cord.
For PLUG CABLE EQUIPMENT, the socket outlet should be installed
near the equipment and should be easily accessible.
3
Care and Maintenance
Care
l
l
l
l
Avoid exposing your monitor directly to sunlight or other heat
sources. Place your monitor away from the sun to reduce glare.
Put your monitor in a well-ventilated area. Do not place anything
heavy on top of your monitor.
Make certain that your monitor is installed in a clean and
moisture-free area.
Keep your monitor away from magnets, motors, transformers,
speakers, and TV sets.
Safety Tips
l
If smoke, an abnormal noise or an odor comes out of your monitor,
switch off the power immediately and call our service center.
Never remove the rear cover of your monitor cabinet. The display
unit inside contains high-voltage parts and may cause an electric
shock.
l
l
Never try to repair the monitor yourself. Always call your service
center or a qualified technician to fix it.
Note: This user’s manual contains graphics and information that is for
reference purposes only and is subject to change without notice.
4
CHAPTER 1
Introduction
BEFORE INSTALLING YOUR MONITOR
Read this manual cover to cover.
PAY ATTENTION to all WARNING and CAUTIONS
DO NOT use computer components not recommend by the
manufacture
Do not attempt to service the monitor your self. If a problem
occurs, contact the manufacture's authorized service center
ABOUT YOUR MONITOR
This monitor is a microprocessor-controlled, color monitor that
uses a TFT LCD panel. The monitor conforms to EPA Energy
Star and VESA DPMS (Display Power Management Signaling)
power management standards.
RGB MODE
This monitor is equipped with a microprocessor that identifies
your computer 's video mode and allows user to adjust the setting.
VIDEO MODE
This monitor can accept the NTSC or PAL signal to display the video
screen automatically. It also implement the video screen on PC
function, we called PIP function. We also provide one pair of BNC
in/out connector inside.
5
FACTORY-PRESET MODES
Table 1 shows standard video mode setting that has been
pre-adjusted at the factory for accurate video display. These setting
are stored in the monitor's memory
Table 1. Factory-Preset Modes
PC mode
Mode
NEC
VGA
Resolution
640x400
640x350
720x400
640x480
640x480
640x480
800x600
800x600
800x600
800x600
1024x768
1024x768
1024x768
1280x1024
1280x1024
H-Freq.(KHz) V-Freq(Hz)
24.83
31.47
31.47
31.47
37.86
37.5
56.4
70
70
60
72
75
SVGA
35.16
37.88
48.08
46.87
48.36
56.47
60
56.3
60.3
72.2
75
60
70
XGA
75
SXGA
63.98
80
60
75
Macintosh 640x480
832x624
35
49.7
48.78
60.241
66.7
74.55
60
1024x768
1024x768
74.927
Video Mode
NTSC
PAL
525 lines, 60 fields
625 lines, 50/60 fields
6
l
LCD-1900VR 19” LCD 8U Rack Display Monitor
Overall Dimension (HxWxD): 394.5 x 436 x 62 mm
Effective Display area (H/V): 376.32 x 301.56 mm
Display colors:
Scan Frequencies:
Horizontal
16.7M colors
31.47K to 80KHz
60Hz to 75Hz
Vertical
Number of Pixels:
Pixel pitch:
Picture Tube:
Power:
1280x1024 pixels
0.294x0.294 mm
19" TFT LCD panel
Input
110-240VAC(auto-sensing)
Frequency: 48-62Hz
45Watts maximum (on)
3 Watts (Power saving off mode)
15pin Mini D-sub (Standard)
1 x stereo input
Consumption
PC RGB Connector:
Audio connector
Speaker
2W x 2
RGB Signals:
Video
Analog RGB 0.7Vp-p/75W
Sync
Separate
Display Data Channel:
Compatibility
Video connector input
S-connector
VESA DDC 1/2B
x 1 (S-Video In)
AV connector
x 3 (one for Composite Video
Two for audio left/right)
x 1 (for YcbCr/Component In)
x 1 (Composite Video In)
Mini D type
BNC connector
Video connector output
BNC connector
x 1 (Composite Video Out)
9
Operations:
User Controls
On/Off Power Button,
+/- and Up/down keys
Auto adjustment, Brightness, contrast
color temperature, Hue, Tint,
Source select, PIP setup
H-position, V-position, OSD position
Audio volume, bass, treble, mute
Load default
On Screen Display
Control Type:
Compatibility:
Digital
IBM and compatible, Apple
Macintosh, NEC
Environmental Limits:
Operating Temp
Storage Temp.
Operating Humidity
Storage Humidity
Agency Approval
EMI
32° to 103°F ( 0° to 40°C )
-4° to 140°F ( -20° to 60°C )
10 to 85% without Condensation
10 to 95% without Condensation
FCC-B and CE
MPR-II
Emissions
Energy Saving
Safety
EPA energy star, VESA DPMS
UL, TUV
10
Chapter 2
PRODUCT PACKAGE
Open the shipping carton and check the contents. If any items are
missing or damaged, contact your dealer immediately.
The package should include the following items
l
l
Analog Color TFT LCD Monitor
Accessory Box:
1.
2.
3.
4.
5.
6.
VGA cable x 1
AC to DC adapter x 1
Power Cord x 1
User’s manual/Warranty Card x 1
Audio cable x 1
Mini DIN/RCA cable (for Component Video In use)
INSTALLING THE MONITOR
The monitor is equipped with an auto sensing power supply for
voltage ranges from 110~240VAC, 60/50Hz. Confirm the line voltage
designation on the rear panel of the monitor.
11
CONTROL FUNCTIONS
The Monitor control functions are located on the lower center of the
front view side. They are shown in the figure below and described in
the following paragraphs.
The control key description
1.
: Power Switch
2. -
: Decrement
3.
: Increment or source select
: Move to the next item
/ Brightness control
: Move to the previous item
/ Brightness control
+
4. Ñ
5. D
6. MENU : Activate the on screen display
function
12
DESCRIPTION
1. : Power switch
Use the power switch to turn ON or OFF power. We
recommend turning your system power on first, then the LCD
monitor.
2. - & + : decrement or increment the value
The two keys are decrement or increment the value or enter
into the sub-menu.
Note: The + key can change the source directly when
de-activation OSD screen.
3. Ñ & D : Select key / Brightness Control keys
The two keys have two functions, controlled by the MENU key.
When activating OSD screen, the two keys are used to select
the wanted adjustment items. When de-activating OSD
screen, these two keys are used to change the Brightness
value.
4. Menu
Press the Menu key to activate the on screen display screen. It
is a toggle key. Press twice to turn off the on screen display
screen. After 30 sec idle time, the OSD screen will
automatically turn off.
13
CHAPTER 3
1024x768
48.5K
60.2
3
Auto Adjustment
- Execute +
VER
XGA-KDC45-5100
ADJUSTING THE MONITOR
VGA OSD main screen
14
1. Each time, when pressing the menu key, the screen will show as
above. You can see the 3mark that means the selected item.
Then you can change the setting through + or -.key.
2. Pressing Sel key to move the arrow down or up. If the selected
item has many option to choose, press – or + to enter into the
sub-menu.
3. Then move the Sel key to item you want to change , the item will
be highlighted as red characters, then press – or + to change the
value.
4. If you finish the setting, press the MENU to key to return to the
main OSD, then repeat the item 2 and 3 to do the changes you
want
The VGA main screen
Auto adjustment
§ Automatically adjusts the phase and position of the LCD monitor for
the best view setting
Color temperature setting
§ Provide 9300K, user mode, and 6500K option
Brightness adjustment
§ Let user adjust the brightness. The range if from 0 to 99
.
Contrast setup
§ Provide user to separately adjust each R, G and B contrast and
intensity value. When Move to this icon, and press – or + key, then the
screen will show below
15
Color
the
do the
balance
balance:
monitor
white
1024x768
60KHz
75Hz
Color balance
Intensity R
Intensity G
Intensity B
Contrast R
Contrast G
Contrast B
-
Execute
+
VER
automatically.
XGA-KD841-5100
Intensity R: Adjust the R color intensity, the range is from 0 to 63
Intensity G: Adjust the G color intensity, the range is from 0 to 63
Intensity B: Adjust the B color intensity, the range is from 0 to 63
Contrast R: Adjust the R color contrast value, the range is from 0 to 63
Contrast G: Adjust the G color contrast value, the range is from 0 to 63
Contrast B: Adjust the B color contrast value, the range is from 0 to 63
16
Geometry setup
§
§
We provide Pixel Clock, Phase, H Position, V Position, OSD H
Position, OSD V Position and Txt/Gft option to change.
Pixel Clock: Adjust the viewing screen size. The range is from 0 to 99
Phase: Adjust phase tracking to reduce the display flicker. The range
is from 0 to 31
§
§
§
§
§
§
H Position: Move the whole screen horizontally. The range is from 0 to
120.
V Position: Move the whole screen vertically. The range is from 0 to
100.
OSD H Position: Move the OSD horizontally. The range is from 0 to
15
OSD V Position: Move the OSD screen vertically. The range is from 0
to 15
Txt/Gfx: Select the display mode as 640x480(graphic mode) or
720x400(text mode).
VCR mode: To enable or disable the VCR mode. If the video source
is come form VCR, the timing is different with DVD or camera. To
avoid the screen shaking, you should VCR mode to enable mode.
Normally, the default setting is OFF.
PIP setup
§
§
We provide H Position, V Position, PIP H/V ratio, Contrast, Intensity,
Tint and Hue option for customer setup the PIP screen.
H Position: Move the PIP screen Horizontally. The range is from 0 to
15.
§
§
V Position: Move the PIP screen Vertically. The range is from 0 to 15.
PIP H/V ratio: Provide four option from 1 to 4. When set as 4, it is 1: 1
ratio as original size. Set as 3, it is 1/2 of original one. Set as 2, it is
1/4 of original one. Set as 1, it is 1/8 of original size.
Contrast: Adjust the contrast value of PIP screen. The range is from 0
to 127.
§
§
Intensity: Adjust the intensity value of PIP screen. The range is from
0to 255.
§
§
Tint: Adjust the Tine value of PIP screen. The range is from 0 to 255.
Hue: Adjust the Hue value of PIP screen. The range is from 0 to 255
Source Select
§ We provide VGA, Composite, S-video, YCbCr, PIP composite, PIP
S-video, PIP YCbCr and PIP off for user’s selection.
17
Note: The PIP function is only valid on video on VGA screen. We can’t
support video on video screen
Speaker volume control
§
§
§
§
§
§
We provide Volume, Bass, Treble, Mute and PIP audio for audio setup.
Volume: Adjust the speaker volume. The range is from 0 to 32.
Bass: Adjust the speaker Bass value. The range is from 0 to 10.
Treble: Adjust the speaker Treble value. The range is from 0 to 10.
Mute: Enable or disable the Mute function.
PIP audio: Enable or disable the PIP mute function
Load the factory default setting.
§ Restore the factory default setting.
18
Chapter 4
VIDEO ADJUSTMENT
Video OSD Screen
15.7K
NTSC
60.2
3
Brightness
-
Adjustment
49
+
VER
XGA-KDC45-5100
1. Each time, when pressing the menu key, the screen will show as
above. You can see the 3mark, that means the selected item
Then you can change the setting through + or -.key.
2. Pressing Sel key to move the arrow down or up. If the selected
item has many option to choose, press – or + to enter into the
sub-menu.
3. Then move Sel key to item you want to change, the item will be
highlighted with red characters, then press – or + to change the
value.
4. If you finish the setting, press the MENU to key to the main OSD,
then repeat the item 2 and 3.
The OSD Main Screen
Brightness adjustment
§ Adjust the screen brightness value. The range if from 0 to 99.
Contrast adjustment
19
§ Adjust the screen contrast value. The range is from 0 to 127
Intensity adjustment
§ Adjust the screen intensity value. The range is from 0 to 255
Tint adjustment
§ Adjust the screen Tint value. The range is from 0 to 127
Hue adjustment
§ Adjust the screen Hue value. The range is from 0 to 255
Geometry setup
§ We provide Sharpness, H Position, V Position, OSD H Position, and
OSD V position.
§ Sharpness: Adjust the screen sharpness level. The range is from 0 to
15
§ H position: Move the screen horizontally. The Range is from 0 to 20
§ V Position: Move the screen vertically. The range is from 0 to 20
§ OSD H Position: Move the OSD horizontally. The range is from 0 to 15
§ OSD V Position: Move the OSD screen vertically. The range is from 0
to 15
§ VCR mode: To enable or disable the VCR mode. If the video source
is come form VCR, the timing is different with DVD or camera. To
avoid the screen shaking, you should VCR mode to enable mode.
Normally, the default setting is OFF.
Source Select
§
we provide VGA, Composite, S-video, YCbCr source for user’s
selection
Speaker volume control
§
We provide Volume, Bass, Treble, Mute and PIP audio for audio
setup.
§
§
§
§
§
Volume: Adjust the speaker volume. The range is from 0 to 32
Bass: Adjust the speaker Bass value. The range is from 0 to 10
Treble: Adjust the speaker Treble value. The range is from 0 to 10
Mute: Enable or disable the Mute function
PIP audio: Enable or disable the PIP mute function
Load the factory default setting.
Load the factory default setting
§
20
Appendix
Troubleshooting Procedures
This LCD Monitor was pre-adjusted in the factory with standard VGA
timing. Due to output timing differences among various VGA cards,
you may initially experience an unstable or unclear display when a
new display mode or new VGA card is selected.
This LCD Monitor Supports Multiple VGA Modes. Refer to the timing
table for a listing of factory-preset modes supported by this LCD
Monitor.
PROBLEM: There is no LCD Display
If there is no display on the LCD, please perform the following steps:
1. Make sure that the power indicator on the LCD Monitor is lit,
all connections are secure, and the system is running on the
correct timing. Refer to the Addendum for information on
timing.
2. Turn off the LCD Monitor and then turn it back on again.
Press the upper Function Control button (refer to Chapter 2)
once and then press either the upper or lower Adjustment
Control button several times. If there is still no display, press
the other Adjustment Control button several times.
3. If step 2 doesn’ t work, connect your PC system to another
external CRT. If your PC System functions properly with a
CRT Monitor but it does not function with the LCD Monitor,
and the LCD Monitor’s power LED is blinking, the output
timing of the PC’ s VGA card may be out of the LCD’ s
synchronous range. Please change to an alternate mode
listed in Addendum or replace the VGA card and repeat steps
1 and 2.
4. If the PC doesn’ t function with the CRT monitor neither, check
BIOS to see if there is a dual scan setting under the display
mode item. Set the BIOS display mode to Dual Scan or
CRT and try again. If there is still no display, then there may
be a problem with your system. Contact technical support.
5. If the power LED is not lit, check to see if the AC power
connector is securely connected. Verify that the AC adapter
LED is lit. If the AC adapter LED is not lit, please contact
your dealer for assistance
21
|