RC930_IB.QXD 10/10/00 1:12 PM Page 1
Wireless Modem Jack
Model RC 930 rev. 3.0
TABLE OF CONTENTS
Safety Precautions .............2
Getting Started ...................4
System Installation .............4
Connecting your Computer.5
Security Programming........6
Trouble-Shooting................7
Things You Should Know...8
Warranty.............................8
Thomson Consumer Electronics
Accessories and Components Business
RC930_IB.QXD 10/10/00 1:12 PM Page 3
Safety Precautions Continued
FCC Part 68 & Class B Notices
Your Wireless Modem System complies with Part 68 of FCC Rules. You must, upon request, provide
the FCC registration number and the REN to your telephone company. These numbers are shown on
the label on the base unit.
This equipment complies with the limits for a Class B digital device as specified in Part 15 of FCC
Rules. These limits provide reasonable protection against radio and TV interference in a residential
area. However, your equipment might cause TV or radio interference even when it is operating
properly. To eliminate interference you can try one or more of the following corrective measures:
•
•
•
Reorient or relocate the receiving antenna
Increase the distance between the system and the radio or TV
Use outlets on different electrical circuits for the equipment and the radio or TV
Read the Troubleshooting section of this manual for directions on remedying the problem.
Lightning
Your Wireless Modem Jack System has built-in protection circuits to reduce the risk of damage from
surges in the telephone line. These protection circuits meet or exceed the FCC requirements.
However, lightning striking the telephone or power lines can damage your system. Lightning damage
is not common. Nevertheless, if you live in an area that has severe electrical storms, we suggest that
you unplug the system during storms to reduce the possibility of damage.
Important Notes On Operation
•
•
•
•
•
Do not plug Modem Jacks into power strips or surge protectors.
Modem Jack Extension does not operate during a power outage.
Modem Jack System can only be used for single phone line.
Be sure to plug Base unit (two jacks on side) in first before Extension unit (one jack on side).
If you cannot get a dial tone, unplug both phone jacks and reset units following the section titled
“Trouble Shooting”on page 8.
•
It is very important that directions are followed in order. In the event of a problem unplug both units,
remove all cords and start again.
Industry Canada Equipment Notice
The Industry Canada label identifies certified equipment. This certification means that the equipment
meets certain telecommunications network protective, operational and safety requirements as
prescribed in the appropriate Terminal Equipment Technical Documents(s). The Department does not
guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the
facilities of the local telecommunications company. The equipment must also be installed using an
acceptable method of connection.
The customer should be aware that compliance with the above conditions may not prevent degradation
of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier.
Any repairs or alterations made by the user to this equipment , or equipment malfunctions, may give
the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility,
telephone lines and internal metallic water pipe system, if present, are connected together. This
precaution may be particularly important in rural areas.
Caution: Users should not attempt to make such connections themselves, but should contact the
appropriate electric inspection authority, or electrician, as appropriate.
3
RC930_IB.QXD 10/10/00 1:12 PM Page 4
Getting Started
Unpacking
Carefully remove units from packaging. If there is any visible
damage, DO NOT attempt to operate the equipment. Notify your
dealer or shipping carrier immediately. Keep this guide for future
use.
System Contents
• Base Unit
The base unit has two
modular telephone jacks on
the right side and a green
indicator light.
• Extension Unit
The extension unit has one
jack on the right side and a green indicator light. This is the
unit that can be moved from location to location to create a
modem jack in an electrical outlet.
• Telephone Cord (6’)
A 6 ft. telephone cord is provided to connect
the base unit to the existing wall phone jack.
Installation
Follow the steps below to install the Wireless Modem Jack System.
NOTE: To ensure proper performance, it is important to
install the Base Unit FIRST then install the Extension Unit.
Also ensure that both units are securely plugged into the wall
outlets.
Base Unit
1. Plug one end of the provided telephone cord into either jack on
the right side of the base unit, and the other end into any
existing wall phone jack.
4
RC930_IB.QXD 10/10/00 1:12.PM Page 5
2. The phone previously used at that location should now be
plugged into the extra jack on the side of the base unit.
3. Now plug the base unit into an electrical outlet.
Wall
Phone JackWall Outlet
Telephone Cord
Base Unit
Extension Unit
4. Plug Wireless Modem Jack Extension unit into an electrical outlet
where you want a new phone jack.
5. Plug telephone’s line cord into the extension unit. There should
now be a dial tone when your phone is taken off the hook.
Connecting to Computer Modem
After installing the base unit (see above), follow these steps to
install the extension unit to the modem RJ-11 outlet.
5
1. Plug Extension Unit into an electrical outlet near your computer
CPU. Do not plug into power strip or surge protector.
2. Unplug telephone from the extension unit if used to test for
dial-tone.
3. Plug telephone line cord from the computer modem jack into
the jack on the side of the Wireless Modem Jack Extension
Unit.
4. Your computer modem is now ready to operate.
Under certain circumstances where static is present in your
telephone line, the Wireless Modem Jack may not filter or remove
such static. This condition can affect computer modem
performance. Try installing the base unit and or the extension unit
in another electrical outlet.
Security Programming
Once steps 1-5 have been completed in the installation sequence
above, and the units have been installed and connected to the set-
top-box, you can now set the security. Follow the easy steps below to
set the security feature for the units.
1.Using a small pointed object,
press the black recessed button
on the side of the base unit. The
green light on the lower front
right hand corner of the base unit
will come on. This will stay lit
during the security programming
sequence. Once the button is pressed, you now have (5) minutes
to program your first extension unit.
2. Now press the black recessed
button on the side of the
extension unit. The green light in
the lower front right hand corner
of the extension unit will flash
once. Programming of that unit
is now complete. (If the green
button is flashing repeatedly, your base unit is not in
programming mode. You will need to go back to step one.)
6
RC930_IB.QXD 10/10/00 1:12 PM Page 7
3. Once all extensions have been coded, you will need to verify
the dialtone at each location.
Your situation (system location, characteristics of the home) can, in
some instances, affect performance and occasional interference
may be experienced. Some static, buzzing or humming at certain
locations within the operating area is possible. However, if you
experience unusual levels of noise, follow the trouble shooting
actions below. If the steps below do not solve your difficulty,
remove both units from the electrical outlets, remove all cords and
reinstall making sure to follow instructions on the previous page.
Trouble Shooting
Most difficulties associated with the Wireless Modem Jack
System are due to improper installation.
If the steps below do not solve your difficulty, remove both units
from the electrical outlets, remove all cords and reinstall making
sure to follow instructions on the previous page.
Your situation (system location, characteristics of the home/office)
can, in some instances, affect performance and occasional
interference may be experienced. Some static, buzzing or
humming at certain locations within the operating area is
possible. However, if you experience unusual levels of noise,
follow the trouble shooting actions below.
PROBLEM
ACTION
No dial tone
Check connections, check outlet for power,
try new cords, move base and/or extension.
Static/
Interference
Move base and/or extension (halogen lamps,
light dimmers, and computer surge
protectors can cause some static).
Can't dial out
Does not ring
Decrease distance between units. If
problems continue call customer service.
Decrease distance between units. If problems
continue call customer service.
7
RC930_IB.QXD 10/10/00 1:12 PM Page 8
Things You Should Know
The following list of situations is provided to inform you of things
that you may encounter when using the system. It is intended to
help you get the best performance possible.
Power Outages
Only the telephone plugged into the base unit operates.
Two-Line Phone Operations
If two lines are being used, only one line can operate through the
Wireless Modem Jack System. A single base and extension hook-
up will only operate the phone line to which the base is connected.
Ground Fault Circuits
It is recommended that the Wireless Modem Jack System not be
set up or operated using GFI circuitry (e.g. bathrooms, outdoor
use, etc.)
One Year Limited Warranty
Thomson Consumer Electronics, warrants that for one year from
date of purchase this product is free from defects in material and
workmanship. If the item is defective within that period, return it at
your expense to the dealer from whom it was purchased together
with proof of purchase for replacement. This warranty excludes
defects or damage due to misuse, abuse, or neglect.
IN NO EVENT SHALL THOMSON CONSUMER
ELECTRONICS BE LIABLE FOR SPECIAL, INDIRECT,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES WHETHER
IN CONTRACT, TORT, OR NEGLIGENCE.
Some states do not allow limitations on how long an implied
warranty lasts or permit the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may
not apply to you.
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
Help Line - For additional set-up help, call us at 800-409-5111
© 2000 Thomson Consumer Electronics, Inc.
Product Exchange Center
11721 Alameda Ave.
Socorro, TX 79927
PRC930IB Rev0400
Trademark(s) ® Registered
Marca(s) Registrada(s)
Made In Indonesia
8
|